Cleveland Convotherm PC-HACCP Manuel d'installation

260AZH REV. B 3/06 This kit connects a PC to as many as 31 Combis at a maximum distance of 3280 Feet (1000 meters). The software can download cooki

10 Attaching the Base Plate to the Communication Module Mount the board to the panel using the spacers and nuts included in the kit.

11Inserting the Communication Module Cable into the Oven Photo 30 Remove the sanitary seal plug from the underside of the Combi.

12Photo 25Photo 26Connect the Network Cable to the Communication Module Take care to match the wire ends or colors to the connections throughout the

13 Setting the Jumpers on the Communication Module Photo 27 Jumper setting for the first Combi and all Combis in the Network. To set the jumpers:

14 Photo 33 Secure cable to the upper right spacer as shown in Photo 36. Photo 35 Place Control Board and Module back in

15Replace the Operation Panel Photo 36 Remount the Operation Panel back into the Combi. Photo 37 Press down and turn clockwise to tighten the Op

16Replace the Control Side Panel Photo 38 Photo 39 Push up and in from the bottom edge of the side panel.

17Directions for Installing the USB Adapter 1. Plug the USB connector into the adapter and connect to one of the USB ports on the back of your com

18 Select install from a list of specific location (advanced) Ignore this screen if it appears:

19 Uncheck “Include this location in the search.” Click Next. Let search

21 Software-CD - 300550 2 Network Connection Cable – 300551 (included only w/ 232 kit) 3 Dongle - C5009210 4 PC Interface Converter - C5009156 (inclu

20 The Hardware wizard will appear a second time:

21 Follow the directions in each screen.

22 Allow search for CD

23 Click Finish to close the screen. Configure your serial device: 1. Right click My Computer, select properties: Then select the “Hardware t

24 Expand the Ports (COM & LPT) device

25 Right click on the “USB Serial Port (COM??)” item. The ?? will be a number greater than 0 and less than 255. Select the Port Settings tab.

26 Note the COM setting. Only COM1, COM2, COM3, and COM4 can be used by the HACCP software. To change the COM number, click the Advanced button.

27 If needed click the COM Port Number: drop menu and select and acceptable port number. If all are marked as (in use) then change one of the other

28For USB to RS485 Switches 1 and 4 are ONFor USB to RS232 Switches 2, 3, 4 are ON 6. Once the computer recognizes the USB adapter, the dip switch

29Jumper #1 Position SHOWS WIRE CONNECTIONS PIN 1, PIN 2, AND GROUND (PIN 6). 7. For the adapter to output data for RS485, a jump

31 Electronic Board (1) – C5019104 2 Connector (1) – C5002091 3 Bracket with Studs (1) – C2114799 4 Control Panel Spacers (2) – C8009030 5 Screws – M

260AZH REV. B Rev Page116 March 2006 This Page for Internal Record Only, Not for Printing Cleveland Range, LLC 1333 East 179th St, Cleveland, Ohio 4

4TO CONNECT THE RS232 CONVERTER TO THE PC Photos 4, 5, and 6 show the correct cable connections from the PC to the PC Converter for RS232. Note the

5NOTE: A: RED WIRE B: BLACK WIRE GROUND: GROUND OR SHIELD WIRE RS232 CABLE CONNECTION FOR CONVERTER TO RS485 ONLY Photo 8 shows the cable connection

6 TO CONNECT USB CONVERTER TO RS485 ONLY IMPORTANT: ALWAYS USE THE SAME USB PORT WHEN REATTACHING THE USB CABLE TO THE PC! See Page 20 for instruct

7Remove the Control Side Cover Turn the 1/4 turn quick-locks to loosen. From the bottom edge of the side panel, push up and pull out. Rem

8 Remove the Control Panel Photo 17 Press down and turn counterclockwise to remove the Operation Panel retention screw. Pho

9Attaching the Base Plate to the Communication Module 1. Mount the board to the panel using the spacers, nuts and washers included in the kit.