Cleveland KEL-40-INS Manuel de réparation

CLEVELAND INSTALLATION, OPERATION AND REPAIR MANUAL CLEVELAND RANGE INC. 1333 East 179th St. Cleveland. Ohio U.S.A. 44110 (216)481-4900 920

OPERATING CONTROLS AND INDICATORS ITEM NO. DESCRIPTION FUNCTION 16 On-Off Toggle Switch ( Pg. 213-09DR ) Controls electrical power to kettle. 2

PARTS LIST - KETTLE BOTTOM ITEM NO. PART NO. DESCRIPTION QTY. 1. F105025 Bleed vent elbow 1 2. KE50570 Bleed vent nut 1 3. F105022 Connecto

KETTLE BOTTOM 10

PARTS LIST - CONTROL HOUSING ITEM NO. PART NO. DESCRIPTION QTY. 1. FA11134 Screw, 10-24 x 3/8"SS 2 2. KE50325 Console cover 1 5. FA9500

CONTROL HOUSING 12

PARTS LIST- POWER TILT OPTION ITEM NO. PART NO. DESCRIPTION QTY. 1. KE51012 Gear box lid 1 2. FA11134 Screw, 10-24 x 3/8" SS 1 3. KE50577 Motor 1

POWER TILT OPTION 14

PARTS LIST - TRUNNION ASSEMBLY ITEM NO. PART NO. DESCRIPTION QTY. 1 KE00354-D Trunnion bearing casting 1 2 KE00351-D Trunnion bearing casting

PARTS LIST - 2" TANGENT DRAW-OFF VALVE ITEM NO. PART NO. DESCRIPTION QTY. 1. to 7. KE50972-B Draw-off assembly 1 1. FA21008 Hex nut 1

PARTS LIST - FAUCET ITEM NO. PART NO. DESCRIPTION QTY. 1 3/4" Spout 1 KE50833 for KS-E-LA KE50828 for KT-20-EA KE50829 for KT-30-EA

CLEVELAND INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS FOR ELECTRIC SELF-CONTAINED KETTLES FLOOR MODELS KEL-25 KEL-25-T SSE-25-L SSE-25-T KE

PARTS LIST - HINGE ASSEMBLY ITEM NO. PART NO. DESCRIPTION QTY. 1.-9. SE00057 Hinge assembly (40 gal. and under) 1 SE00058 Hinge assembly (60

ALL KETTLES AND SKILLETS HINGE ADJUSTMENT INSTRUCTIONS 1. Insert 3/8" Allen wrench. 2. Turn clockwise to relieve tension on spring. 3

ALL ELECTRIC KETTLES SERVICING GUIDE This section contains servicing information intended for use by Authorized Service Personnel. Note 1: If Fault Is

5. Measure continuity across safety thermostat. Is it an open circuit? Yes Replace defective safety thermostat. No Go to step #6. 6. Is there

B/ Problem: Kettle heats too slowly or not hot enough. (Note: normal max. operating pressure with an empty kettle is 25-30 psi.) Possible Causes 1

6. Yes Kettle is operating properly. Turn the potentiometer on the control box clockwise to increase the max. operating temperature. Does the kett

D/Problem: Red LED remains illuminated even though water has been added. Possible Causes 1. Defective low water level probe. 2. Defective co

STANDARD NORTH AMERICAN WIRING DIAGRAM For electrical supply other than shown above, refer to the wiring diagram affixed to the underside of the con

STANDARD EUROPEAN WIRING DIAGRAM For electrical supply other than shown above, refer to the wiring diagram affixed to the underside of the console c

HARRISONS & CROSFIELD (CANADA) LTD. MATERIAL SAFETY DATA SHEET PRODUCT: ETHYLENE GLYCOL

INSTALLATION INSTRUCTIONS WARNING: Installation of this kettle must be accompanied by qualified electrical installation personnel working to all app

PRODUCT: ETEYLENE GLYCOL DATE: 24 October 1986 FIRST AID: EYES: Flush with water for at least 15 mi

PRODUCT: ETEYLENE GLYCOL DATE: 24 October 1986 VII. SPILLS & LEAK PROCEDURES STEPS TO BE TAKEN IF MATERIAL

SECTION I PRODUCT INFORMATION NAME OF PRODUCT FINNAN 1524L and 1529L PURPOSE OF PRODUCT Closed System Corrosion Inhibitor CHEMICAL NAME Mix

SECTION V HEALTH HAZARD DATA A - EFFECTS OF ACUTE OVEREXPOSURE (A) SKIN Corrosive to skin, may cause dermatitis. (B) INHALATION For nitrite

SECTION IX PROTECTION INFORMATION RESPIRATORY PROTECTION: LOCAL EXHAUST MECHANICAL EXHAUST

ELECTRIC SERVICE CONNECTION Install in accordance with local codes and/or the National Electric Code ANSI/NFPA No. 70-1990 (USA) or the Canadian Elect

5. If the kettle is a tilting model, tilt the kettle forward. The red "low water" light should be lit when the kettle is in a tilted po

To check the gauge for proper vacuum after venting, the temperature can be quickly reduced by filling the kettle with cold water. If the kettle will n

DISTILLED WATER REQUIREMENTS Kettle Capacity When Red "Low Water Light'' Comes on, Add Distilled Water When the

9. Pour the contents of the kettle into an appropriate container by opening the draw-off valve or tilting the kettle forward. Care should be tak

5. Rinse kettle interior thoroughly, then dram the rinse water. 6. Leave the cover off when the kettle is not in use. 7. Using mild soa